龙门刨床的可逆直流调速系统的设计

附开题报告,论文,调研报告,图,外文翻译,字数:18756.页数:54    论文编号:JD370  

摘     要
直流电机具有良好的工作特性与运行性能,因而广泛应用于实验室和工厂的精密机床上。本文根据电力电子技术和自动控制的理论基础，设计出了一套适用于龙门刨的调速系统。采用可控硅整流装置对龙门刨的主拖动电机供电，节省了变压器和可控硅的设备容量，达到了经济、线路简单、易于调整的目的。改变直流电动机的电枢电压来进行调速，实现龙门刨床的额定调速范围，简化了控制线路。主电路采用三相桥式反并联的形式，之中对调速系统的控制电路，逻辑环节都作了比较详细的介绍，同时也提供了调速系统的动态性能的分析，最后还给出了基本的系统调试方法。经系统控制模拟试验，该系统方案具有投资小、重量轻、可靠、高效、维修方便等优点。

关键词：直流电动机；龙门刨床；逻辑无环流；动态性能

Abstract
　With good characteristics and performance, the dc motor is widely used in the laboratory and on the precision machine tool in factory. This article according to the electric power and electronic technology and the automatically controlled theoretical, design one, it is systematic to be suitable for the speed of adjusting planed in Longmen. Adopt silicon controlled rectifier rectification device pull to what Longmen plane electrical machinery supply power mainly, have save the capacity of equipment of the voltage transformer and silicon controlled rectifier, has achieved economy, simple, easy purpose to adjust of circuit. Is it realize with Armature electric current wide to transfer in the speed range, simplify the circuit of controlling rapidly to transfer jointly. Main circuit adopt three-phase bridge parallel form instead, In exchange jobs speed systematic control circuit, that link make comparisons detailed introduction of, is it transfer speed systematic quiet, dynamic analysis of performance to offer too at the same time, provide basic system debug the method also finally. This system designs have some advantages through system control simulation test with a small amount investment, light, high efficiency, convenient for repairing and soon.

Key word: DC motor, Longmen planning, Logical lossless circulating current, Dynamic performance
目    录
摘　　要…………………………………………………………………………………I
Abstract……………………………………………………………………………………II
第１章  绪论…………………………………………………………………………………1
　　1.1 龙门刨床的生产过程简介…………………………………………………………1
1.2 龙门刨床的工艺特点及其对自动控制系统的要求………………………………2
1.3 主拖动电动机的选择………………………………………………………………3
1.4 设计指标……………………………………………………………………………4
第2章  调速系统的方案选择………………………………………………………………5
2.1 拖动方案……………………………………………………………………………5
2.2 电动机供电方式的选择……………………………………………………………5
2.3可控硅整流电路型式的确定………………………………………………………6
　　2.4控制方案的确定……………………………………………………………………7
第3章  主回路设计…………………………………………………………………………9
3.1 整流变压器计算……………………………………………………………………9
3.2 可控硅元件选择……………………………………………………………………11
3.2 均流电抗器计算……………………………………………………………………13
3.3 平波电抗器计算……………………………………………………………………13
第4章  交流侧和直流侧保护计算…………………………………………………………15
4.1过电流保护………………………………………………………………………15
　　4.2过电压保护………………………………………………………………………16
4.3 可控硅关断过电压保护……………………………………………………………21

第5章  控制回路设计………………………………………………………………………22
5.1给定积分器………………………………………………………………………22
　　5.2电流闭环…………………………………………………………………………23
5.3速度闭环……………………………………………………………………26
5.4逻辑无环流环节……………………………………………………………………26　　
5.5 静止检测器…………………………………………………………………………31
5.6 直流稳压源…………………………………………………………………………32
第6章  控制系统动态参数计算……………………………………………………………34
6.1参数设置方案确定…………………………………………………………………35
　　6.2电流闭环参数计算………………………………………………………………35
6.3 速度环参数计算……………………………………………………………………39
6.4 系统动态指标计算…………………………………………………………………43
第7章  操作回路设计………………………………………………………………………44
第8章  系统的调试…………………………………………………………………………46
6.1系统的安装及检查…………………………………………………………………46
　　6.2调试过程…………………………………………………………………………47
    8.3 小结…………………………………………………………………………………50
结    论……………………………………………………………………………………51
参考文献……………………………………………………………………………………52
致    谢……………………………………………………………………………………53
附录A  (系统总电路图) …………………………………………………………54

 WORD格式全文下载链接(充值:128元)

龙门刨床的可逆直流调速系统的设计......