电气工程论文网


  • 首页|
  • 自动化毕业论文|
  • 电子机电毕业论文|
  • 电子通信论文|
  • 电气工程论文|
  • 电子信息工程|
  • 电气工程原创论文|
  • 电气工程免费论文|
原创毕业论文 → 电气工程专业原创毕业论文   现成毕业论文范文 → 电气工程专业毕业论文范文

论文降重

当前位置:电气工程论文网 -> 电子信息工程论文下载 -> 基于单片机的脉冲燃烧热水炉控制器

基于单片机的脉冲燃烧热水炉控制器

本文ID:LW19645 字数:6028,页数:27

论文编号:DZXX350  论文字数:6028,页数:27  附任务书,开题报告,中期检查 
摘  要
 在能源日趋紧张,环境保护日益受到重视的今天,脉冲燃烧技术的推广应用具有特别重要的意义,目前世界各国对脉冲燃烧的研究也越来越多。本文所设计的采用AT89S51单片机控制的脉冲燃烧热水炉,对系统的稳定运行及合理利用硬件资源带来满意的效果。
 本文主要讨论了以AT89S51单片机为核心的硬件电路设计和软件程序的设计,通过传感器对水温水位等的检测数据送至单片机,控制各个继电器的开启和关闭,并且通过LED实时显示温度。另外还有熄火检测及报警电路,从而实现热水炉的全自动管理:自动供气、自动点火、自动进水、出水温度、水箱水位控制、水温连续检测及数字显示;熄火时,能自行启动的自保护功能和水温超高、水位超限处理能力。使热水炉在无人状况下也能安全可靠的运行。
关键词  脉冲燃烧;温度控制;熄火检测;水位控制


ABSTRACT
 Increasing tension in the energy, environmental protection, more and more attention today, the wide application of pulse combustion technology is of particular importance, the current world research on the pulse combustion more and more. This article is designed using AT89S51 MCU-controlled pulse combustion heater system for stable operation and the rational use of available resources, with satisfactory results.     This paper discusses the AT89S51 microcontroller core with hardware design and software design, through sensors such as temperature and water level test data sent to the microcontroller to control all relays open and close, and real-time through the LED display temperature. There are also flame detection and alarm circuits, in order to achieve fully automatic water heaters Management: Automatic gas, automatic ignition, automatic water, water temperature, water tank level control, temperature detection and continuous digital display; flame, can start their own self-protection and high water temperature, water level gauge processing. Making water heaters in the absence of conditions can be safe and reliable operation.
 Keywords:  Pulse combustion;Temperature Control;Water level control;Flame detection
 
 目  录
摘  要 3
ABSTRACT 4
第1章  绪  论 1
1.1  选题背景及意义 1
1.2 本文所做的工作 1
第2章 脉冲燃烧热水炉原理 2
2.1  脉冲燃烧热水炉结构 2
2.2 脉冲燃烧热水炉燃烧原理 3
第3章 系统硬件设计 4
3.1 系统总体功能概述 4
3.2 核心芯片选择 5
3.3 复位电路及按键 7
3.4 水位传感器 9
3.5 温度测量及A/D转换模块 9
3.6 熄火检测 10
3.7 继电器和光耦 11
3.8 显示电路 12
3.9 报警电路 13
第4章 系统软件设计 15
4.1 系统主程序 15
4.2 初始化子程序 16
4.3 按键识别子程序 17
4.4 熄火检测保护子程序 18
4.5 水位及水温控制子程序 19
4.6 水温采样子程序 21
结论 22
致谢 23
参考文献 24

下载地址 WORD格式全文下载链接(充值:118元)

基于单片机的脉冲燃烧热水炉控制器相关论文
论文人工降重

本论文《基于单片机的脉冲燃烧热水炉控制器》在电子信息工程论文下载栏目,由电气工程论文网整理,转载请注明来源 www.dqlunwen.top 更多论文,请点电气工程论文查看
上一篇:十字路口交通灯 下一篇:基于单片机的火灾自动报警系统
点击查看关于 基于 单片机 脉冲 燃烧 热水 控制器 的相关论文题目 2011-05-10 09:18:32【返回顶部】
联系方式

相关栏目

光机电应用技术
机电一体化
应用电子技术
电子信息工程技术
自动化免费论文
自动化专业毕业论文
电子专业免费论文
电子机电毕业论文
电气工程免费论文
测控技术与仪器
电气工程原创论文
电子通信论文
电气自动化开题
电子机电开题报告
电子通信免费论文
PLC相关外文翻译
电子机电信息外文翻译
电子通信外文翻译
联系方式
电子信息工程论文下载
电气工程论文下载


联系方式


电气工程论文网提供电气工程论文范文,电气工程毕业论文,网站永久域名www.dqlunwen.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2022 电气工程论文网 版权所有