基于松下FPX的四层电梯控制系统设计

论文编号:ZD938    论文字数:11491,页数:45

摘   要

 随着社会的不断发展，高层建筑越来越多，而电梯已成为了高层建筑楼房中必不可少的设备。目前电梯控制系统主要有三种控制方式：继电器电路控制系统（早期安装的电梯多位继电器控制系统）、PLC控制系统、微机控制系统。继电器控制系统由于故障率高，可靠性差，控制方式不灵活以及消耗功率大等特点，目前已逐渐被淘汰。微机控制系统虽在只能控制方面有较强的功能，但也存在抗干扰性差，系统设计复杂，一般维修人员难以掌握及修理技术等缺陷。而采用PLC控制系统大大提高了电梯可靠性、可维护性以及灵活性，延长了使用寿命，同时缩短了电梯的开发周期。近年来，PLC在工业控制领域内得到十分广泛地应用。松下FPX系列PLC是松下公司推出的小型PLC，其功能非常强大。本文介绍了，用松下FPX作为控制器的四层电梯控制系统设计， 并进行了实验调试。实践证明，基于松下FPX的可编程控制器设计的电梯控制系统，具有良好的性能。
 
关键词：自动控制; PLC；电梯控制

Abstract
 
 
 As society continues to develop, the higher buildings are more and more. The elevator became a high-rise building to house the equipment. There are currently three types of elevator control system control mode: relay control system (early installation of the elevator control system of a number of relay), PLC control system, computer control system. Relay control systems as High failure rate, unreliable and ineffective control mode, power consumption is very large has gradually been eliminated. Although computer control system can control the function of strong, but there is poor anti-interference, system design complexity, General maintenance and repair personnel could not master the technology and other defects. Using PLC control system has greatly enhanced the reliability of the lift, maintainability and flexibility to extend the service life of the elevator at the same time shorten the development cycle. So in recent years, PLC get in the field of industrial control is widely used. FP-X PLC is the recently introduced small PLC, its function is very powerful. This paper describes the use of Panasonic FP-X to write a four-story elevator control procedures and test procedures for elevator operation. Practice shows that, based on Panasonic FP-X Programmable Controller elevator control system has good application value.
 
 

Keywords:  automatic control; PLC; Elevator control
 
   
 
目 录
摘 要…………………………………………………………………………………….……………...I
Abstract………………………………………………………………………………………….…...Ⅱ
1 绪论………………………………………………………………………………………………...…1
1.1 电梯控制研究的背景及意义…………………………………………….……….…………..1
1.2 电梯的发展和分类……………………………………………………………………………...2
1.2.1  电梯的分类………………………………………………………………………….……2
1.2.2  电梯的发展………………………………………………………………………….……2
2 系统总体设计………………………………………………………………………………………4
2.1 电梯总体结构………………………………………………………………………………….4
2.2 电梯控制系统总体设计………………………………………………………………………..5
3 电梯控制系统硬件设计......………………………………………………………………….....6
3.1 电梯控制系统电路设计………………………………………………………………………6
3.2  电梯PLC的选型…………………………………….………………………………………..6
3.2.1 输入输出（I/O）点数的估算……………………………………………………………7
3.2.2 存储器容量的估算………………………………………………………………………7
3.2.3 控制功能的选择…………………………………………………………………………7
3.3 电梯控制系统接口电路设计….………….………….…………………….…….……….…13
3.3.1  FP-X通讯设置….………………….…………………….….….….….….…….………13
3.3.2  PLC输入输出地址分配…...…………………………………………………………..14
3.3.3  PLC输入输出接线图…..………..………….………………………………………….16
4 电梯控制系统软件设计……………………………………………………..………….……..17
4.1 电梯控制系统实现的功能………………………………………………………………….17
4.2 电梯程序设计流程图……………………………………………………………….....……18
4.3 PLC程序设计..…..…….…….…….……………………..………………………..…………19
4.3.1 开机初始化程序..…….…….…….…………………..…………..……………..………19
4.3.2 内呼信号控制程序.…….…….…….……………….…………………..…………….19
4.3.3 外呼信号控制程序.…….…….…….……………………..……………..…………….20
4.3.4 开关门控制程序.……..…….……………………..……………………..…………….22
4.3.5 电梯上行下行控制程序.…….…….………………………..…………..…………….24
4.4  PLC程序调试……………………………………….…………………………………….…29
5 结论……………………………………………………………….…………………….…...31
致谢……………………………………………………………………………………..........32
参考文献…………………………………………………………………………………..….………33
附录………………………………………………………………………………………..….………34

 WORD格式全文下载链接(充值:168元)

基于松下FPX的四层电梯控制系统设计......