电气工程论文网


  • 首页|
  • 自动化毕业论文|
  • 电子机电毕业论文|
  • 电子通信论文|
  • 电气工程论文|
  • 电子信息工程|
  • 电气工程原创论文|
  • 电气工程免费论文|
原创毕业论文 → 电气工程专业原创毕业论文   现成毕业论文范文 → 电气工程专业毕业论文范文

论文降重

当前位置:电气工程论文网 -> 测控技术与仪器 -> 集成运放综合参数测试仪

集成运放综合参数测试仪

本文ID:LW16810 字数:13418,页数:36 字数:13418,页数:36

论文编号:CK058   论文字数:13418,页数:36

摘  要
 本系统参照片上系统的设计架构、采用FPGA与SPCE061A相结合的方法,以SPCE061A单片机为进程控制和任务调度核心;FPGA做为外围扩展,内部自建系统总线,地址译码采用全译码方式。FPGA内部建有DDS控制器,单片机通过系统总线向规定的存储单元中送入正弦表;然后DDS控制器以设定的频率,自动循环扫描,生成高精度,高稳定的5Hz基准测量信号。扫频信号通过对30MHz的FPGA系统时钟进行分频和外部锁相环(FPGA采用FLEX10K10无内部锁相环)倍频,产生高频率稳定度、幅值稳定度的扫频信号。放大器参数测量参照GB3442-82标准,低频信号幅度的测量采取AD高速采样,然后进行数字处理的方法;高频信号的幅度直接采用集成有效值转换芯片测得。A/D转换采用SPCE061A内部自带的10位AD。SPCE061A主要实现用户接口界面(键盘扫描、液晶显示、数据打印以及其他服务进程的调度)、AD转换以及测量参数(Vio Iio Kcmr Avd BWG Tr)计算、与上位机通信等方面的功能。上位机主要实现向下位机发送测量指令、与下位机交换测量数据、以及数据的存储、回放、统计。

关键词:参数测量、运算放大器、DDS、FPGA、SPCE061A、数字信号处理

Abstract
The system with reference to the design of system-on-chip architecture, used a combination of FPGA and SPCE061A approach to the process of SPCE061A single chip core control and task scheduling; FPGA for external expansion, internal self-system bus, address decoding the full translation code approach. There DDS internal FPGA controller, microcontroller through the system bus to the provisions of the storage unit into the sine table; DDS controller and then to set the frequency, automatic cycle of scanning, to generate high precision and high stability of the baseline measurement 5Hz signal. Sweep signal of 30MHz for the FPGA system clock frequency and external phase-locked loop (FPGA using FLEX10K10 no internal phase-locked loop) frequency, high frequency stability, amplitude stability of the sweep signal. Amplifier parameters measured by reference to the standard GB3442-82, low-frequency signal amplitude measurements taken by sampling high-speed AD and then proceed to the method of digital processing; high-frequency signal directly proportional to the magnitude of the integrated chip measured RMS conversion. A / D conversion using internal SPCE061A own 10 of the AD. SPCE061A main user interface (keyboard scanning, liquid crystal display, data printing and other services for the activation process), AD conversion, and measurement parameters (Vio Iio Kcmr Avd BWG Tr), the host computer and communications functions. PC main crew sent down measurement instructions, and under the exchange of measurement data-bit machines, as well as data storage, playback, and Statistics.

Key words:measurement of operational, amplifier parameters, DDS, FPGA, SPCE061A, digital
signal processing

目 录
摘要……………………………………………………………………………….……………..I
Abstract………………………………………………………………………….…………….Ⅱ
1 前言…………………………………………………………………………………………..1
2 总体方案设计………………………………………………………………………………3
2.1  集成运算放大器的主要性能参数……………………………………………………3
2.2  系统方案比较设计与论证…………………………...…………………………….....3
 2.2.1  测量电路模块………………………………….……………………………...4
 2.2.2  信号采集模块…………………………………….……….......………………6
 2.2.3  用户接口模块………………………………………….……...………………6
2.3  整机工作原理与功能实现…………………………………………………...……….7
2.4  软件系统………………………………………………………………………………9
2.5  其他系统扩展…………………………………………………………………………11
3  各子模块的设计…………………………………………………………..……………...12
 3.1  输入电压4~40mV、输入电流0~4mA 量程转换………………………………….12
 3.2  静态参数与动态参数的测量………………………………………………...………12
 3.3  5Hz 4V 有效值正弦波的实现……………………………….………...………….…12
 3.4  单位增益带宽测试………………………………………………………………...…13
 3.5  自动测量功能的实现………………………………………………………………...14
 3.6  显示模块……………………………………………………………………………...14
 3.7  键盘模块……………………………………………………………………………...15
 3.8  UART-PC 机通讯……………………………………………………………...……...16
4  理论计算及分析……………………………………………………………………….....17
 4.1  开环放大倍数的测量……………………………………………………...…………17
 4.2  输入失调电压的测量…………………………...……………………………………18
 4.3  输入失调电流的测量………………………………………………………..……….19
 4.4  共模抑制比的测量…………………………………………………………………...20
 4.5  -3dB 带宽F0…………………………………………………………………………20
 4.6  转换速率(SR)和上升时间的测量……………………………………………….….21
5  电路图及有关设计文件………………………………………………………………..22
 5.1  电源电路…………………………………………………………………………….22
 5.2  单片机、FPGA 系统板电路………………………………………………………..23
5.3  测量电路……………………………………………………………….……………24
 5.4  精密整流电路……………………………………………………………………….24
 5.5  低通滤波电路………………………………………………………………………..25
6  系统测试…………………………...……………………………………………………...27
 6.1  测试仪器……………………………………………………………………………..27
 6.2  测试数据…………………………………………………………………..…………27
 6.3  抗干扰措施…………………………..………………………………………………28
7  总结………………………………………………………………………………………...30
致谢…………………………………………………………………………………………......31
参考文献…………………………………………………………………………………….....32

下载地址 WORD格式全文下载链接(充值:158元)

集成运放综合参数测试仪相关论文
论文人工降重

本论文《集成运放综合参数测试仪》在测控技术与仪器栏目,由电气工程论文网整理,转载请注明来源 www.dqlunwen.top 更多论文,请点电气工程论文查看
上一篇:面向化工产品检测技术的研究 下一篇:基于单片机的函数信号发生器设计
点击查看关于 集成 综合 参数 测试仪 的相关论文题目 2011-04-01 16:38:13【返回顶部】
联系方式

相关栏目

光机电应用技术
机电一体化
应用电子技术
电子信息工程技术
自动化免费论文
自动化专业毕业论文
电子专业免费论文
电子机电毕业论文
电气工程免费论文
测控技术与仪器
电气工程原创论文
电子通信论文
电气自动化开题
电子机电开题报告
电子通信免费论文
PLC相关外文翻译
电子机电信息外文翻译
电子通信外文翻译
联系方式
电子信息工程论文下载
电气工程论文下载


联系方式


电气工程论文网提供电气工程论文范文,电气工程毕业论文,网站永久域名www.dqlunwen.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2022 电气工程论文网 版权所有